worm gear speed reducer

Single reduction worm gearing provides high ratio reduction with couple of shifting parts in a close-coupled compact drive. The proper angle arrangement of driving-to-driven machine requires a the least space. Input and result shafts can be prolonged in either or both directions in horizontal or vertical plans adaptable to any installation requirement. Efficient motor speeds are decreased to gradual speed requirements of several industrial machines in one reduction.
Product Features
Ratios 5:1 to 70:1
Hollow & Solid Output Shafts
Vertical & Horizontal Mounting
Fan Cooled (Standard)
Motor Mounts (C-Face Adapters or Scoops)
Cast Iron or Metal Housings
Products
The exclusive usage of the involute Helicoid Thread form (with leaving side contact) on the worm and gear provides for high efficiencies, and long service existence. The hardened surface and polished alloy steel worm develops a clean, work hardened surface on the bronze gear. Because of this worm gears use in and improve with prolonged service while additional gears are wearing out. EP offers a wide selection of model configurations, sizes, ratios, and add-ons from our standard product line.
Fabricated Designs
If your application involves severe shock loads or possible housing damage from external sources (as in steel mills or mobile gear applications) EP can provide fabricated steel housings with up to 48″ center distances. Fabricated housings provide optimum rigidity and strength which allows the tranny of higher horsepower amounts than are feasible with standard cast iron models. Extra heavy side plates connect the worm and gear shaft bearing facilitates, assuring correct meshing of the apparatus under all load conditions. In smaller sizes, fabricated steel reducers are interchangeable with EP regular cast iron reducers.
Custom Designs
EP can provide custom speed and reversed engineered reducers for your application, be it a new project or a direct drop-in replacement for a competitor’s swiftness reducer. Fabricated metal reducers allow EP to match a competitor’s footprint, centerline, and shaft elevation allowing a direct drop-in alternative saving the customer time and money.
Long – Quiet Life
All worm gears in EP reducers are produced from phosphorous bronze. Our design also includes a hardened, ground and polished alloy steel worm. This combination develops a clean, work-hardened mating surface of the bronze equipment which enhances with prolonged service.
Worm gearing is a course of equipment reducers that utilizes correct angle, nonintersecting shafts. This form of reducer provides smooth and quiet operation and permits the probability of large swiftness reductions. These gears are available from stock in a wide selection of ratios, from only 4:1 to as much as 3600:1. The compact design and structure allows worm equipment reducers to be positioned in a relatively small space. Thus, very high reductions in a limited package size can be achieved with this configuration. Our worm gear features the continuous sliding tooth action between worm and the teeth. This escalates the tolerance for heavy loads and shock loads. Worm gear drives offer users high reducing capacity for relatively low cost when compared to some other types of gearing.
The use of worm gearing extends across many industries including food, beverage and grain and has many applications. Some applications that use worm gearing are: conveyors, mixers and bucket elevators.
EP worm gear reducer gearbox series bottom on years of encounters uses designed teeth surface with unsurpassed torque transfer performance with great efficiency, efficency and cost.Worm gear system transmits power through sliding contact, leading to extremely low vibration , noise, little backlash and self-locking property
-Housing:One time we casting creats great rigidity for severe impacts. Outer cooling fins and inner lubrication essential oil diversion channel design to improve heat dissipation.
-Worm Shaft: Manufactured with Carbon alloyed Metal S45C or SCM415, precison machined and carburized to HRC45 or HRC60, after that for precision tooth grinding to ensure maximum contacting.
-Worm Wheel: Manufactured with Carbon alloy ALBC2, teeth are machined by precision CNC hobbing machine to sustain high impact.
A worm gear reducer is one kind of reduction gear package which consists of a worm pinion input, an output worm equipment, and features a right angle result orientation. This kind of reduction gear container is normally used to have a rated motor speed and produce a low speed output with higher torque worth based on the decrease ratio. They often can resolve space-saving problems because the worm equipment reducer is one of the sleekest decrease gearboxes available because of the small diameter of its output gear.
worm gear reducerWorm gear reducers are also a favorite type of acceleration reducer because they provide the greatest speed decrease in the tiniest package. With a high ratio of speed reduction and high torque output multiplier, it’s unsurprising that lots of power transmission systems make use of a worm gear reducer. Some of the most typical applications for worm gears are available in tuning instruments, medical assessment equipment, elevators, security gates, and conveyor belts.
SW-1 and SW-5
Torque Transmission provides two sizes of worm equipment reducer, the SW-1 and the SW-5 and both are available in a variety of ratios. The SW-1 ratios include 3.5:1 to 60:1 and the SW-5 ratios include 5:1 to 100:1. Both these options are manufactured with tough compression-molded glass-fill up polyester housings for a long lasting, long lasting, light-weight speed reducer that’s also compact, noncorrosive, and nonmetallic.
Features
Our worm equipment reducers offer an option of a solid or hollow result shaft and feature an adjustable mounting position. Both SW-1 and the SW-5, however, can endure shock loading better than other reduction gearbox styles, making them well suited for demanding applications.
Rugged compression-molded glass-fill up polyester housing
Light-weight and compact
Non corrosive
Non metallic
Range of ratios
SW-1, 3.5:1 to 60:1
SW-5, 5:1 to 100:1
Grease Lubrication
Solid or Hollow output shaft
Adjustable mounting position
Worm Equipment Reducers also referred to as worm gearbox or worm velocity reducers. Worm equipment reducers are used for speed reduction and increasing the torque for electrical engine drives. You can decide to mount your NEMA motor to the reducer by using the NEMA C encounter flange or use a coupling. If you need a coupling for the output or input shaft discover our coupling section for selecting a coupling. We offer four assemblies left hand and right hand and double result shaft and shaft insight and shaft result. Interchangeable with many worm gear manufactures. Find data sheet in item overview for diamensions. Unless you see your type, make sure you Contact Us.
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Design for OEM Replacement
Double Bearings Applied to Both Shaft Ends
Anti-Rust Primer Applied Outside and inside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Metal Shafts
Flange Mount Versions for 56C and 145TC Motors
EP DDVM series triple-reduction worm gear quickness reducers can be found in ratios from 5000:1 to 175,000:1 and center distances from 7” to 20” (larger sizes on request). Output torque ranges from 33,000 in lbs. for the 7” CD DDVM-70 to 582,900 in pounds for the DDVM-200. Mechanical HP insight requirements are from 0.09 HP for the 175,000:1 7 in CD reducer to 6.25 HP for the 5000:1 20” CD unit. These reducers are available in four configurations: horizontal, vertical, shafted, and shaft installed.
These reducers are well suited for water/waste-water equipment drive applications such as thickeners and clarifiers, which need a vertical straight down shaft. Other offered configurations also make EP triple reduction reducers perfect for make use of on mixers, elevators, solar panels, astronomical telescopes, indexing tables, hoists, conveyors, or additional process or components handling systems where huge torques/gradual speeds are needed.
These reducers are also obtainable with a helical major reduction stage and are termed the HDVM series
Product Features
Ratios 5000:1 to 175,000:1
HP from 0.09 to 6.25.
Output Torque to 583,000 in lbs.
Output RPM only 0.01 with a 1750 RPM input.
Ideal for ultra-slow quickness, high torque applications
8 Ratios Available from 5:1 to 60:1
7 Gear Box Sizes from 1.33 to 3.25″
Universally Interchangeable Style for OEM Replacement
Double Bearings Used on Both Shaft Ends
Anti-Rust Primer Applied Inside and Outside Gearbox
Shaft Sleeve Protects All Shafts
S45C Carbon Metal Shafts
Flange Mount Versions for 56C and 145TC Motors
Description
The HDR Series worm gear reducers are used in low to moderate horsepower applications to reduce speeds and increase torque. Worm gear reducers are available in direct or indirect drive, direct drive versions are 56C or 145TC flange mount with either right, remaining or dual output shafts or a hollow bore output. The indirect drive versions are shaft input-shaft result boxes for use with sprocket or pulley drive systems. They provide an effective low cost solution to speed reduction and increased torque, with higher tolerances for shock loading than helical equipment reducers.
In order to select a gearbox speed reducer, you will need to determine the required torque and support factor for the application. Click on “Specs” above for a desk that will aid in determining the service element. For service elements above 1.0, multiply the mandatory torque by the service factor.
Our standard 700 Series – the heart of EP velocity reducer product line – has been serving industry reliably for over 40 years. Its verified modular style has set the sector standard for overall performance and is the most imitated product in the current worm gear speed reducer market. But why settle for a knock-off when you can have the original – from EP.
Specifications
11 basic single reduction sizes
8 basic dual reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in stock)
Product Features
The 700 Series’ huge oil reservoir provides efficient heat dissipation and lubrication for longer operating life.
Its multi-position mounting versatility allows for installation in practically any position.
Housings are straddle-milled, top and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged housing, fabricated of fine-grained, gear-quality cast iron, provides maximum strength for maximum durability, and also greater precision during worm and gear alignment.
EP 700 Series high-strength bronze worm gear is straddle mounted between heavy-duty tapered roller bearings to improve thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill up, level, and drain in virtually any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal lifestyle.
Both 2D and 3D CAD drawings are available in our eCatalog.
TheIncreased Quality! Industrial Rated! Inexpensive!One-piece gearcase, without exterior ribs, is made from close-grained cast iron and for rigid gear and bearing support. It also offers excellent temperature dissipation.Dual lip, spring-loaded seals guard against oil leakage and prevent dirt from entering.Stepped shafts with oversized ball andtapered roller bearings.Carbon metal shafts for greater power.High tensile strength cast bronze worm wheel and hardened and surface alloy steel worm made intregal with the shaft for long and trouble-free life.Oil sight gauge for ease of maintenance (not available on sizes 25 and 34).Factory oil filled.Every unit test run prior to shipment.Universal installation with bolt-on feet.Highly modifiable design.All this at substantially reduced prices than you have been accustomed to paying for reducers of lesser quality. Less

Tags

Gearbox-worm

As one of leading gearbox-worm manufacturers, suppliers and exporters of mechanical products, We offer gearbox-worm and many other products.

Please contact us for details.

Mail: [email protected]

Manufacturer supplier exporter of gearbox-worm.

Recent Posts